With white fixtures, keep your floors and all tile white or a stone that is mostly white. You can paint the walls above the wainscot (which might be glossy painted wood or beadboard, or you might employ a cabinet for the sink that was painted a very soft sky blue. One narrow trim piece of tile running through the white tile might be the same tone of sky blue. Then, add blue linens / towels / etc. [houzz=] Now, consider what other colors are in your home and select one that is clear and soft and lovely with white. You might use that color instead of sky blue. I used sky blue because it is the color of water and therefore always appropriate in the bath, but you can make the bath flow with the colors you have or plan to have in your home. If this was a master bathroom instead of a common or guest bath, I would shift the choices of stone and tile from white plus white to a lovely off-white, cream, or almond tone - like travertine. Use a neutral like chocolate on the cabinet and add color only with linens and perhaps some art on the wall. [houzz=]

I am so happy to see you here! I will have to go back and see if i can retrieve my posts... thought I would make them into a little book for my daughter, with photos. Quick run-down on the bathroom (not travels, no time) - The kitchen has a rather elegant sliding door with beveled glass panels. Painted white, since this was the original colour. GD's new bathroom has the doors I had picked earlier; i thought of polishing them but decided sprayed automobile paint (on a resin primer) would wear better. Especially since it is such a small bathroom, and she is so splashy. I have this finish in my kitchen and it has lasted 15 years now. A tad chipped here and there, but only needs a wipe down once a week. Same finish for the balcony doors, also split like the bathroom. We have a new wardrobe, a study table with built-in shelves, and a small chest of drawers for her odds and ends. I want to re-tile the tiny balcony, more as a little statement. Currently we are looking at Portuguese tiles, though I did think a mosaic with a funky cat might be nice. Let me see the costing. The room will be painted a neutral adobe, with bright white woodwork and an off-white ceiling. This means she can go wild with cushions and covers. Other changes in the flat; We have changed the glass in the master bedroom and living room from small cramped panes to a single pane for each section with a 1" bevel all round. Doubles the cost of the glass, but looks so elegant! The air-conditioning is being re-located. The compressors were all mounted in the bedroom and living room balconies, which looked terrible and meant the balconies (very narrow, only 30" deep) couldn't be used for anything. Not even plants. So they are being moved so that the compressors can be mounted at the rear of the building. two down, one to go. Now we can put in some nice plants, fishtail palms etc. The kitchen counter on one side came out intact and will be reused elsewhere. I am planning overhead storage, cupboards, and a draining cupboard for plates and glasses. Right now there is no dish washer, though a place is earmarked, but for now I will put in a cupboard with steel racks for cups, glasses and plates, all hidden behind pressed glass doors. This is all in the planning stage.... Pictures in a little while, they are mostly on my ipad and don't transfer well to the mac. They come without numbers... so I have to rename the or something. Somebody tell me how to do this!

Thanks a lot for your comment. I wouldn't exactly call it a walk in-closet. As you can see from the drawing, Its space provided for two single wardrobe (one on each side). Maximum width can be around 3.5 ft. The humidity point is quite relevant. The question is would it be possible to include a wet room in the space i.e. 6ft x 8.6ft. - considering I don't remove the dress wall. Wanted to get a sense on the possible layout. Thanks and look forward to your advise.

I suggest you follow the step-by-step guide for creating storage cabinets under the bathroom sink. Take proper measurements - Measure the available available space in height, width and height. Cut Plywood to size - With a circular saw and framing square, cut all the required pieces out. You can use a sliding compound saw as an alternative. Attach the base and sides - Start assembling the sink cabinets by placing the bottom piece of plywood sheet on a flat surface. Attach the back and top boards - Place the plywood sheet for the top part of the cabinet and attach wood screws to connect it to both the sides. Turn the back faces of the cabinet upwards. Keep the back piece over the structure and fix it into place with wood screws. Attach shelves - Place the cabinet in an upright position to install the shelves. Slide a shelf into the structure so it is flush against the back. Attach door - Keep both hinges of the door on the same side of the plywood sheet. Drill them using wood screws into place. Now keep the door over the cabinet structure, extend the hinges to one of the side panels and fix them to make them secure. Fix a hasp closure on the other side of the door, placing it in the center of the hinges.