Are you saying you will be layering a wooden false wall on top of the existing wall to hold the pocket door? If that is the case, you might want to treat the entire side of that new and existing wall ( including the area above doorway) as an accent wall using wood veneer strips. They look like actual pieces of wood plank which have adhesive backing, they come in a variety of finishes and colors...I like the old reclaimed wood look. A diagonal pattern would add extra visual interest, but would be more intense to cut and install. That will camouflage the additional layer and create a beautiful accent wall.

To hide a window above your bed and make it soundproof, use soundproof curtains or heavy blackout drapes to block noise and light. Install a removable window plug made with acoustic foam and mass-loaded vinyl for effective noise reduction. Alternatively, consider placing acoustic panels or a built-in bookshelf over the window. You can also extend your headboard or use frosted films and blinds for an aesthetic, soundproofing solution that blends seamlessly.

Madam, I don’t have a drawing. However, I can draw and send it across. Sorry for advising, however my suggestion would be: 1) Check the tube level of the wall for plaster. 2) Ensure that the plaster is even 3) You can ask Asian paints home solution for a coat of paint. Don’t look beyond a cement colour. 4) Leading upto the wall have it decked with wood; meaning deck wood flooring. This will accentuate the floor. 5) Buy a Buddha resting on a pedestal. The Buddha must be sculpted in stone. Take care that the face is natural. 6) Get a Carpenter to make a frame work on all four sides with teak and give it a natural finish. 7) Bodhi tree must be silver/ gold finish and must cover atleast 40% of the wall. 8) Have two focus lamps from the top and one warm lighting from the floor level. 9) Just one pot with either artificial or natural bamboo with a few green leaves. Lo and behold you will have the most beautiful entry into both your bedrooms. Useful for meditation as well. 1) Bodhi tree- Mantra Arts, Chennai. I am chennai based and hence no idea of other cities. 2) Pots-try Poettery, Gurgaon. True masterpieces. Regards, Prakash.

1.Remove Door and Trim If you're adjusting an existing door frame in your house, first, you will have to remove the door itself and all of the trim surrounding the frame. The door is simple enough; just pull the hinge pins out of place, tapping them from beneath with a screwdriver and mallet if necessary. For the trim, wedge a flat pry bar underneath the edge on one end of a section, and gently pull the casing away from the wall. Do the same thing for all of the pieces around the door frame and carefully set them aside to reuse later. 2.Square the Opening Off It is difficult to ensure that a door will be level and square if the rough opening is not (the rough opening is the bare bones structure before any work is done to begin a door install). So, before you begin, use a carpenter’s square to check the upper corners. This will save you time and effort later on. Remember, the more accurate your measurements, the more level your door will be. 3.Shim Door Frame Placing a pre-hung door in the rough opening will give you an idea of how it will ultimately fit. This type comes complete with a pre-made frame surrounding it, so all you need to do is carefully slide it into place and shim wherever you need around the frame to level it in the opening. Remember that wooden shims can simply be made of wedges or blocks of wood. Place a level against the door frame in your existing installation to see where you need adjustments. Then, like before, place wooden shims until it sits as it's supposed to. To keep the shims in place, nail them to the hinge. Make sure you trim any excess pieces with a saw so they sit flush with the wall. 4.Get a Level Sill Next, adjust the door sill with a flat bar or wedge until it too is level. Place the wedge or bar under the latching side of the door frame and have your help hold your door so you can check to make sure whether the top of the frame, or lintel, will need more adjustment. 5.Double Check It is important in every project to double check your work. Take the time to measure the gap between the door frame and the original rough opening. Use and nail in more wedges where necessary. If you have the extra set of hands to spare, have someone re-measure if you feel it could be adjusted differently. 6.Secure Door Frame in Opening Place your blocks of wood and/or shims into the open space over the lintel, and begin attaching the door frame to the original rough opening. Again, double check each corner to be square, before completely securing it into place. Note: Do not worry about the finishing touches just yet. You can add framing to the door after applying the paneling or drywall. Also, head and side casings will finish off a new installation nicely, covering all your small shim adjustments. Thanks & Regards, Cathrinfrancis URBELITE Bangalore