I like this tile as well. Very sleek and mod looking. I would consider running it vertically instead of the picture horizontal pattern. It might give the illusion of more height in the shower surround. The color is great. If you are worried about it being "too much," you could always see if they have the same tile in a different shade and mix the two or doing one wall in a contrasting (lighter) color. I personally like it as long as you have good lighting.

I am so happy to see you here! I will have to go back and see if i can retrieve my posts... thought I would make them into a little book for my daughter, with photos. Quick run-down on the bathroom (not travels, no time) - The kitchen has a rather elegant sliding door with beveled glass panels. Painted white, since this was the original colour. GD's new bathroom has the doors I had picked earlier; i thought of polishing them but decided sprayed automobile paint (on a resin primer) would wear better. Especially since it is such a small bathroom, and she is so splashy. I have this finish in my kitchen and it has lasted 15 years now. A tad chipped here and there, but only needs a wipe down once a week. Same finish for the balcony doors, also split like the bathroom. We have a new wardrobe, a study table with built-in shelves, and a small chest of drawers for her odds and ends. I want to re-tile the tiny balcony, more as a little statement. Currently we are looking at Portuguese tiles, though I did think a mosaic with a funky cat might be nice. Let me see the costing. The room will be painted a neutral adobe, with bright white woodwork and an off-white ceiling. This means she can go wild with cushions and covers. Other changes in the flat; We have changed the glass in the master bedroom and living room from small cramped panes to a single pane for each section with a 1" bevel all round. Doubles the cost of the glass, but looks so elegant! The air-conditioning is being re-located. The compressors were all mounted in the bedroom and living room balconies, which looked terrible and meant the balconies (very narrow, only 30" deep) couldn't be used for anything. Not even plants. So they are being moved so that the compressors can be mounted at the rear of the building. two down, one to go. Now we can put in some nice plants, fishtail palms etc. The kitchen counter on one side came out intact and will be reused elsewhere. I am planning overhead storage, cupboards, and a draining cupboard for plates and glasses. Right now there is no dish washer, though a place is earmarked, but for now I will put in a cupboard with steel racks for cups, glasses and plates, all hidden behind pressed glass doors. This is all in the planning stage.... Pictures in a little while, they are mostly on my ipad and don't transfer well to the mac. They come without numbers... so I have to rename the or something. Somebody tell me how to do this!

I suggest you follow the step-by-step guide for creating storage cabinets under the bathroom sink. Take proper measurements - Measure the available available space in height, width and height. Cut Plywood to size - With a circular saw and framing square, cut all the required pieces out. You can use a sliding compound saw as an alternative. Attach the base and sides - Start assembling the sink cabinets by placing the bottom piece of plywood sheet on a flat surface. Attach the back and top boards - Place the plywood sheet for the top part of the cabinet and attach wood screws to connect it to both the sides. Turn the back faces of the cabinet upwards. Keep the back piece over the structure and fix it into place with wood screws. Attach shelves - Place the cabinet in an upright position to install the shelves. Slide a shelf into the structure so it is flush against the back. Attach door - Keep both hinges of the door on the same side of the plywood sheet. Drill them using wood screws into place. Now keep the door over the cabinet structure, extend the hinges to one of the side panels and fix them to make them secure. Fix a hasp closure on the other side of the door, placing it in the center of the hinges.

Thanks for both of your responses CUBSpaces team and Shweta from Shades studio. It really gives a clarity about possible consequences. I am now doubt free about changing whole things in Bathroom as it will be interconnected. However will appreciate your opinion on few things: 1. Kitchen wall tiles: I have those from countertop height to roof(almost area of 6X15 feet) which are good and not hollow. I changed countertop 5 years back without any damage to these tiles. It might cost me another 10-15 K, but I feel the whole process and quantity of wasting old good tiles makes me little sad. 2. kitchen countertop: Made new around 5 years back. I don't expect to get it all intact. But large pieces can be cut and can be used as top for other freestanding structures like dishwasher, front load washer, heighten base cabinets, etc. 3. Plywood: I don't mind giving enough labour charges for old sheets recycle. I am planning to use doors, loose sheets(like kept on bed frame of settee frame.) or parts of big frames like settee. I am keen on reducing waste than to save money. You can see various DIY ideas by western people, who remove or sand laminates and re-paint furniture, or carefully remove hollow tiles and re-attach them. Some are also re-painting ceramic tiles. I am just asking myself: Are we creating more and more waste by use and throw approach every 10-15 years, just because we can afford it?