A houzz contributor, not too long ago, had made a wine rack out of 4'x4' wooden pallets, that are used in the US to move a load of goods with a fork-lift truck. Perhaps they have them in your country. He cut them in half so they were only two feet deep and stacked them up to high counter height. The wood would be a nice contrast with your concrete, might add a little warmth to the space. cascio.offsite@gmail.com

I am so happy to see you here! I will have to go back and see if i can retrieve my posts... thought I would make them into a little book for my daughter, with photos. Quick run-down on the bathroom (not travels, no time) - The kitchen has a rather elegant sliding door with beveled glass panels. Painted white, since this was the original colour. GD's new bathroom has the doors I had picked earlier; i thought of polishing them but decided sprayed automobile paint (on a resin primer) would wear better. Especially since it is such a small bathroom, and she is so splashy. I have this finish in my kitchen and it has lasted 15 years now. A tad chipped here and there, but only needs a wipe down once a week. Same finish for the balcony doors, also split like the bathroom. We have a new wardrobe, a study table with built-in shelves, and a small chest of drawers for her odds and ends. I want to re-tile the tiny balcony, more as a little statement. Currently we are looking at Portuguese tiles, though I did think a mosaic with a funky cat might be nice. Let me see the costing. The room will be painted a neutral adobe, with bright white woodwork and an off-white ceiling. This means she can go wild with cushions and covers. Other changes in the flat; We have changed the glass in the master bedroom and living room from small cramped panes to a single pane for each section with a 1" bevel all round. Doubles the cost of the glass, but looks so elegant! The air-conditioning is being re-located. The compressors were all mounted in the bedroom and living room balconies, which looked terrible and meant the balconies (very narrow, only 30" deep) couldn't be used for anything. Not even plants. So they are being moved so that the compressors can be mounted at the rear of the building. two down, one to go. Now we can put in some nice plants, fishtail palms etc. The kitchen counter on one side came out intact and will be reused elsewhere. I am planning overhead storage, cupboards, and a draining cupboard for plates and glasses. Right now there is no dish washer, though a place is earmarked, but for now I will put in a cupboard with steel racks for cups, glasses and plates, all hidden behind pressed glass doors. This is all in the planning stage.... Pictures in a little while, they are mostly on my ipad and don't transfer well to the mac. They come without numbers... so I have to rename the or something. Somebody tell me how to do this!

A good tile installer that knows what he is doing, can easily remove that single piece of tile.... carefully replace it with another one. Do you have another extra pieces of the same tile? Do you know what brand and color the existing grout is? That will be more of the issue trying to get the grout match to match up or the finding the same tile (in the same dye lot) if you need to buy another tile. Did the heat cause the break or did a pan bang into the glass? Consider installing a heat resistant Lumicor or 3 Form panel behind the stove. Any flat material that can be sandwiched between two resin panels. 1). Crushed glass. 2). Fabric. 3). Fabric. 4). Fabric.

I suggest you follow the step-by-step guide for creating storage cabinets under the bathroom sink. Take proper measurements - Measure the available available space in height, width and height. Cut Plywood to size - With a circular saw and framing square, cut all the required pieces out. You can use a sliding compound saw as an alternative. Attach the base and sides - Start assembling the sink cabinets by placing the bottom piece of plywood sheet on a flat surface. Attach the back and top boards - Place the plywood sheet for the top part of the cabinet and attach wood screws to connect it to both the sides. Turn the back faces of the cabinet upwards. Keep the back piece over the structure and fix it into place with wood screws. Attach shelves - Place the cabinet in an upright position to install the shelves. Slide a shelf into the structure so it is flush against the back. Attach door - Keep both hinges of the door on the same side of the plywood sheet. Drill them using wood screws into place. Now keep the door over the cabinet structure, extend the hinges to one of the side panels and fix them to make them secure. Fix a hasp closure on the other side of the door, placing it in the center of the hinges.