Hi Ni, I just thought of something....did you say you planned to do the stencil motifs on the window wall? If so, I am thinking they will be mostly hidden by the curtains. I wonder if it might be better to stencil the long wall that is on the right side of the room when looking toward the window. I could see this being a pretty backdrop to the prayer box (I think that’s what you called it?) and your wood cuttings. Then maybe the opposite wall (the one with the kitchen doorway) could hold a large piece of art?

I am so happy to see you here! I will have to go back and see if i can retrieve my posts... thought I would make them into a little book for my daughter, with photos. Quick run-down on the bathroom (not travels, no time) - The kitchen has a rather elegant sliding door with beveled glass panels. Painted white, since this was the original colour. GD's new bathroom has the doors I had picked earlier; i thought of polishing them but decided sprayed automobile paint (on a resin primer) would wear better. Especially since it is such a small bathroom, and she is so splashy. I have this finish in my kitchen and it has lasted 15 years now. A tad chipped here and there, but only needs a wipe down once a week. Same finish for the balcony doors, also split like the bathroom. We have a new wardrobe, a study table with built-in shelves, and a small chest of drawers for her odds and ends. I want to re-tile the tiny balcony, more as a little statement. Currently we are looking at Portuguese tiles, though I did think a mosaic with a funky cat might be nice. Let me see the costing. The room will be painted a neutral adobe, with bright white woodwork and an off-white ceiling. This means she can go wild with cushions and covers. Other changes in the flat; We have changed the glass in the master bedroom and living room from small cramped panes to a single pane for each section with a 1" bevel all round. Doubles the cost of the glass, but looks so elegant! The air-conditioning is being re-located. The compressors were all mounted in the bedroom and living room balconies, which looked terrible and meant the balconies (very narrow, only 30" deep) couldn't be used for anything. Not even plants. So they are being moved so that the compressors can be mounted at the rear of the building. two down, one to go. Now we can put in some nice plants, fishtail palms etc. The kitchen counter on one side came out intact and will be reused elsewhere. I am planning overhead storage, cupboards, and a draining cupboard for plates and glasses. Right now there is no dish washer, though a place is earmarked, but for now I will put in a cupboard with steel racks for cups, glasses and plates, all hidden behind pressed glass doors. This is all in the planning stage.... Pictures in a little while, they are mostly on my ipad and don't transfer well to the mac. They come without numbers... so I have to rename the or something. Somebody tell me how to do this!

Dear Mr Venugopal, Hope your flooring project has come out elegant. Hope you spend some quality time with your new project. @Ms. Preeti, thank you for your compliments. These comments truly mean a lot to us and this is what keeps the team motivated and going. For your knack of reading, I recommend you check the following ethnic styles. for flooring/ceiling/wall options : 1. Jaipur cobalt blue based porcelain products or blue pigments as wall paint/ceiling paint A lost art, remnant of Persian influence, promoted by ancient Moroccan immigrant artiste. 2. Bishnupur/ Haripur terracotta tiles- mughal art form on indian clay palette. Incredibly beautiful to behold and imparts a timeless elegance to ethnic structures. 3. Odisha terracotta art panels- Remnant of same Mughal dynasty. Artiste carve objects of delight using modern clay kilns. Districts- Kendujhar, Sonepur, Khordha and Balangir. 4. Bidriware ceiling tiles - Metallic panels with heavy inlay work . Remnants of Persian Artefacts. 5. Marble inlay works and marble floor medallions- Mughal architecture, colorful setting often inspired by flora and fauna or geometric islamic patterns. Craftsmen mostly from Rajasthan. 6. Khiching Black chlorite floor medallions/ wall panels/ Stone Bathtub and Sinks- Traditional odia ethnic patterns hand carved on Black Chlorite stone. One of the hardest stone in India. Objects include large format floor tiles and solid stone bathtubs. Imparts a stunningly modern perspective to structures. Exclusive to Mayurbhanj district, Odisha . (We are soon to start an export house on the stone based bathware/wall panels/ floor panels) 7. Stone jaalis of Jaipur -Indo-Persian architectural element- intricately carved geometric/floral jaalis for wall panels and cutouts. 8. Compressed Bamboo tiles from Assam- Traditional material with modern technologies- excellent insulating properties and easy to lay-an alternative to wooden flooring. 9. Mother of pearl inlay/ wall tiles -Iridiscent tiles for ultra-luxury -Persian element- Supposedly interacts with the body to calm the senses. Skilled craftsmen from Hyderabad, Mumbai, Kolkata and Lucknow. 10. South Indian Oxide flooring in traditional floral motifs and geomtric patterns- Red, Blue and Yellow are primary oxides. Available as Athangudi tiles . 11. Limestone paste , mud and cowdung flooring for sustainable buildings -zero energy flooring , pest repellent and could be used over existing floor slabs with proper sealing. Compatible with mud houses and concrete as well. Incredibly rustic and long lasting element. 12. Odisha stone wall panels/tiles - Made traditionally of sandstone, chlorite or granites . Traditional odia motifs hand carved over stones. Labour intensive process and recommended for contemporary fusion settings. Found in Khordha, Puri and Mayurbhanj districts. 13. Wooden floor/wall motifs - Mughal element of geometric patterns and floral designs. adds definite interest to any wooden flooring/ wall panelling. Skilled craftsmen available in UP- Shahranpur, Agra, Lucknow and throughout Jammu and Kashmir. These are only a few popular elements. For further research, books on traditional temple architecture, Mughal architecture are recommended. Regards, Aurum Ideas and Spaces Bhubaneswar

Hi, From your Question, I understand that you are looking to integrate a built-in DW and MW in an existing modular kitchen in your home or a new one you have ordered from a kitchen cabinet manufacturer. In either case, your first phone call should be to your kitchen supplier who fitted / will be fitting the kitchen cabinets. Here's WHY? The kitchen cabinet supplier will confirm the size of appliance required as per the kitchen design. They must have made suitable provisions in the cabinets to accommodate these equipments inside cabinets. The cabinets for DW and MW are different from the rest, since the DW sits directly on the floor while MW needs an escape vent at the back for hot air. 2. You need to confirm whether there exists 15 amp power points at appropriate places for each equipment. 3. For built-in DW, a water inlet and outlet at correct positions are required. The kitchen vendor and/or the built-in DW supplier will visit your home and do PDI to mark the exact location of electrical / plumbing points. It will be useful if the kitchen vendor and plumber / electrician are at hand during this PDI, so as to check and discuss relevant issues on the spot and give their confirmations ( or alternatives ) and close this essential issue to the satisfaction of all concerned. Usually, the actual spot is marked on the wall itself and a line drawing showing kitchen cabinets with exact electrical / plumbing positions marked clearly on it, are shared with relevant agencies to eliminate mistakes, if any. Any corrections reg electrical / plumbing will be expensive and time consuming once the cabinet and countertops are fitted. The appliances are typically installed at the end of the project, when all other works are done and almost all agencies ( read workers ) engaged in the premises have left. So, any mismatch between the initial discussion and actual execution comes to light too late in the day !! To avoid this scenario, ask the built-in equipment supplier to visit once more and verify if their requirements are met. Oftentimes, appliance cos. take refuge in such 'non-compliant' provisions and avoid delivering on committed guarantee / warranty, in case of issues at a later date. It's better to go through this cycle once initially, and get everything right in one go. It is also worth noting here that the positions of electrical / plumbing points vary with brands and models, so once you freeze the brand and model, it is advisable not to change the decision thereafter. However, if your kitchen cabinet maker is a pro and experienced, you may just leave it to him and sit back. A good company / professional will take care of all this. Most of the points mentioned above come with a steep learning curve and are not in any book. They don't teach this in any professional design / architecture course. Once all above is sorted....just check out prominent brands in your city / region. Some names that have stood the test of time are SIEMENS / HAFELE / KAFF / ELICA. All of them have a reasonably good service set up which will get top 'selection criteria' in my book. Also, most of them have enough machines out in the field and that means they are likely to have common spares etc with them, when needed down the years. It is a good idea to buy appliances from a single brand as that saves you the trouble of calling different companies for each appliance. Regarding specific model selection....most machines have all the basic features that are commonly used. A MW may have 58 ( so to speak ) pre settings that you may never use unless you are a Chef. Ask your wife and/or leave this to the family member who will spend most time in kitchen. MW with grill / convection features is a good choice and all above brands have them. Hope this answers your Question, and apologize for a loooong reply. But it's better to know relevant issues and decide. Thanks and good luck :)