How do you decorate your place, what kind of style, colors, and feelings? That will greatly influence the type of door you might want. Also, think of your budget, and whether you want to install it yourself or hire a professional (you don't need to tell us, just keep that in mind). Then look around Houzz, in the products page, they have lots of interior sliding doors and hinged ones, from elegant frosted glass in a dark wood frame, to rustic reclaimed wood planks. You may not want to purchase that exact model, but it might give you a better idea of what would fulfill your airflow needs without sacrificing style.

Hi Padmaja, im pooja talwar, for maximum utilization of space u need to break in balconies if u have one and get french windows right till ground level. so you can have a lovely dining area there or low ground sitting area where u can get outside view and spacious look too. doors which open inwards or outwards can be split into 2 so the door flaps become smaller . use mirrors huge ones carved ones on walls to reflect a larger room. also u will have to place furniture which is smaller in size . shoe racks , and cabinets can be made tall instead of having it on ground .... place on the wall hanging shelves , tall cabinets , and storage cabinets. tv can be placed on wall done up with wooden pannel. have storage up on ceiling edges rather than any where down. hope these lil suggestions help you

1.Remove Door and Trim If you're adjusting an existing door frame in your house, first, you will have to remove the door itself and all of the trim surrounding the frame. The door is simple enough; just pull the hinge pins out of place, tapping them from beneath with a screwdriver and mallet if necessary. For the trim, wedge a flat pry bar underneath the edge on one end of a section, and gently pull the casing away from the wall. Do the same thing for all of the pieces around the door frame and carefully set them aside to reuse later. 2.Square the Opening Off It is difficult to ensure that a door will be level and square if the rough opening is not (the rough opening is the bare bones structure before any work is done to begin a door install). So, before you begin, use a carpenter’s square to check the upper corners. This will save you time and effort later on. Remember, the more accurate your measurements, the more level your door will be. 3.Shim Door Frame Placing a pre-hung door in the rough opening will give you an idea of how it will ultimately fit. This type comes complete with a pre-made frame surrounding it, so all you need to do is carefully slide it into place and shim wherever you need around the frame to level it in the opening. Remember that wooden shims can simply be made of wedges or blocks of wood. Place a level against the door frame in your existing installation to see where you need adjustments. Then, like before, place wooden shims until it sits as it's supposed to. To keep the shims in place, nail them to the hinge. Make sure you trim any excess pieces with a saw so they sit flush with the wall. 4.Get a Level Sill Next, adjust the door sill with a flat bar or wedge until it too is level. Place the wedge or bar under the latching side of the door frame and have your help hold your door so you can check to make sure whether the top of the frame, or lintel, will need more adjustment. 5.Double Check It is important in every project to double check your work. Take the time to measure the gap between the door frame and the original rough opening. Use and nail in more wedges where necessary. If you have the extra set of hands to spare, have someone re-measure if you feel it could be adjusted differently. 6.Secure Door Frame in Opening Place your blocks of wood and/or shims into the open space over the lintel, and begin attaching the door frame to the original rough opening. Again, double check each corner to be square, before completely securing it into place. Note: Do not worry about the finishing touches just yet. You can add framing to the door after applying the paneling or drywall. Also, head and side casings will finish off a new installation nicely, covering all your small shim adjustments. Thanks & Regards, Cathrinfrancis URBELITE Bangalore

So you want to construct the kitchen along the two 7' length walls facing each other and along the 9' wall that joins them? It can be done if the space is used practically. But first please share your floor plan to show the position of the doors and windows too. Only then can once figure out how best to utilise the space