This is wonderful how you opened the stairs - you get a real sense of the architecture and it brings in more light. I applaud what you have accomplished. I'm going to assume that the wall above is patched with quickcrete and the whole thing is painted (try to get the wall beyond under the stair too). If you have / want a flat screen, you might mount a swing arm wall mount for a flat panel television on the vertical wall element remaining on the right - just about 3' - 3 1/2' (around 1 meter) above the floor so that it is eye level when you are sitting. The swing arm support will allow you to tilt the television away from the wall ever so slightly across the nearby corner. This can help to eliminate glare from the nearby window and make it possible for more people in the room to view it / expand your seating possibilities. I reference something like http://www.cdw.com/shop/products/Chief-Thinstall-TS318SU-Medium-Dual-Swing-Arm-Wall-Mount-18in-Extension/2555661.aspx?cm_mmc=ShoppingFeeds-_-GoogleBase-_-Video/Monitors/Cards/Projector-_-2555661_Chief%20Thinstall%20TS318SU%20Medium%20Dual%20Swing%20Arm%20Wall%20Mount%20-%2018%22%22%20Extension%20-%20_CIF-TS318SU You can even mount a television tlhat is wider than the wall behind as it can sit flat on the wall and extend beyond the wall to the left when at rest like another plane in your architectural composition. Since the upper stair is just behind, this should be fairly safe for the electronic. Determine precisely where the television will be at rest before you hang the mount itself. Then, look for a low height chest to sit below the television. Ideally a chest with one open shelf near the top to hold your component receivers. You may want to try to run electrical to the remaining vertical wall on the right (the support for the stair landing) to get power into the wall itself, while everything is open. Depending upon where the nearest source is, with concrete walls, you could mount the power junction box low on the wall under the stair and drill out small diameter cord passages through the wall after placement of your components. Or use the baseboard area to run needed cables and power to the area behind the chest, then conceal it with baseboard trim. The more you can hide the power and connection cords, the sleeker the look, to match your gorgeous architectural stair element. If you have a larger deeper television, put it on a sideboard chest under the upper stair where you have the depth. In the rear area, take care with putting cables together in a cord cover - ikea has a good one that is inexpensive. http://www.ikea.com/us/en/catalog/products/20097954/ so it looks "neat" from behind when you come down the stair.

I suggest you follow the step-by-step guide for creating storage cabinets under the bathroom sink. Take proper measurements - Measure the available available space in height, width and height. Cut Plywood to size - With a circular saw and framing square, cut all the required pieces out. You can use a sliding compound saw as an alternative. Attach the base and sides - Start assembling the sink cabinets by placing the bottom piece of plywood sheet on a flat surface. Attach the back and top boards - Place the plywood sheet for the top part of the cabinet and attach wood screws to connect it to both the sides. Turn the back faces of the cabinet upwards. Keep the back piece over the structure and fix it into place with wood screws. Attach shelves - Place the cabinet in an upright position to install the shelves. Slide a shelf into the structure so it is flush against the back. Attach door - Keep both hinges of the door on the same side of the plywood sheet. Drill them using wood screws into place. Now keep the door over the cabinet structure, extend the hinges to one of the side panels and fix them to make them secure. Fix a hasp closure on the other side of the door, placing it in the center of the hinges.

Thanks, for the reply. Yes, I am hoping to feature the mdf on the wall. I am not sure like which one to choose and how to make it look better. I want to make use of the entire wall with cabinets. But, I am open to other options also. There is also a pillar next to the wall on the left side. I also want to make use of the space between pillar and wall (like glass cabinets). Needs your inputs, if you can share some images, that will be great.

Hi Anamika, Duco paint is definitely a good option as it provides clean and rich look, but yes it is costly as well. Cross check if it fits into your budget and you can do accordingly.