These are a tough find! I do know that they get a lot of furnishing items form Mitchell Gold http://www.mgbwhome.com/. I could not find the lighting on there, but, you may want to occasionally check their website. They are going to set up a Good Wife furnishing collections soon :) sorry I couldn't help!

I am so happy to see you here! I will have to go back and see if i can retrieve my posts... thought I would make them into a little book for my daughter, with photos. Quick run-down on the bathroom (not travels, no time) - The kitchen has a rather elegant sliding door with beveled glass panels. Painted white, since this was the original colour. GD's new bathroom has the doors I had picked earlier; i thought of polishing them but decided sprayed automobile paint (on a resin primer) would wear better. Especially since it is such a small bathroom, and she is so splashy. I have this finish in my kitchen and it has lasted 15 years now. A tad chipped here and there, but only needs a wipe down once a week. Same finish for the balcony doors, also split like the bathroom. We have a new wardrobe, a study table with built-in shelves, and a small chest of drawers for her odds and ends. I want to re-tile the tiny balcony, more as a little statement. Currently we are looking at Portuguese tiles, though I did think a mosaic with a funky cat might be nice. Let me see the costing. The room will be painted a neutral adobe, with bright white woodwork and an off-white ceiling. This means she can go wild with cushions and covers. Other changes in the flat; We have changed the glass in the master bedroom and living room from small cramped panes to a single pane for each section with a 1" bevel all round. Doubles the cost of the glass, but looks so elegant! The air-conditioning is being re-located. The compressors were all mounted in the bedroom and living room balconies, which looked terrible and meant the balconies (very narrow, only 30" deep) couldn't be used for anything. Not even plants. So they are being moved so that the compressors can be mounted at the rear of the building. two down, one to go. Now we can put in some nice plants, fishtail palms etc. The kitchen counter on one side came out intact and will be reused elsewhere. I am planning overhead storage, cupboards, and a draining cupboard for plates and glasses. Right now there is no dish washer, though a place is earmarked, but for now I will put in a cupboard with steel racks for cups, glasses and plates, all hidden behind pressed glass doors. This is all in the planning stage.... Pictures in a little while, they are mostly on my ipad and don't transfer well to the mac. They come without numbers... so I have to rename the or something. Somebody tell me how to do this!

1.When to Pull the Trigger The first step in calculating your ROI is to examine your existing lighting. It might be strange to hear this from a company that manufactures LED fixtures, but the technology is not the right fit for every facility and budget — at least not yet. Project managers should be wary of any company or salesperson that tries to claim otherwise. The next decade will likely bring new capabilities and cheaper technology. If you have a facility full of modern fluorescents that are well-placed, you may be wise to switch to LED fixtures in phases. Begin with the areas where LED light can have the biggest impact, like high-volume production lines, warehouse aisles, cold storage and cranes. These areas can suffer significant productivity losses when lighting goes out and stopping production during normal shifts is not an option. The best results from a full LED retrofit will be seen in facilities still using metal halides or other high-intensity discharge lamps, as LEDs have the potential to cut lighting-related energy expenses in half and decrease overall energy use by up to 50 percent. 2.The Site Visit: They Should Come To You Once you’ve decided on an LED retrofit, the first step is a site visit. There is no universal standard or equivalency formula that ensures quality coverage when switching out metal halides, flourescents and LED fixtures. Each type of fixture distributes light differently, so a 1-to-1 fixture swap rarely produces the ideal coverage. Because of that, any responsible lighting project design should begin with an in-person inspection. Light levels are impacted by a variety of factors including placement, obstructions, wall colors and the amount of dirt and dust present. The same plan won’t work for a cold storage facility in Houston that works for a manufacturing plant in Kansas, even in a building with the same square footage.If companies offer over-the-phone or over-the-Internet quotes based on the idea of equivalencies, they are offering rough estimates, not guarantees. On the other end of the spectrum, specialty firms also charge exorbitant fees for engineer-designed layouts. Good project management includes a no- or low-cost site visit in your scope of work and a specialized layout that is part of a larger project management cost. 3.A Good Quote: It’s a Workhorse, Not a Unicorn There are three key elements to project management: quality, service and price. Every manager wants the unicorn — a company that delivers high-end products for a low price with services like installation and rebates. But that’s not a sustainable business plan. If companies promise you the impossible, or even just a high-end fixture at a bargain price, they’re probably stretching the truth to make the sale. Be leery.Instead, a good quote offers expert advice, outlining how you should devote your project resources to maximize your ROI. If your budget is limited, or allocated over a five-year period, then a strong quote will include installation in phases. The quote is your blueprint, so it should focus on your goals and resources instead of offering canned options or simply replacing halides or fluorescents. A well-designed LED layout will account for changes in light distribution because LED output is more focused horizontally and vertically than light from older technologies. You’ll likely need grid adjustments involving electricians and other contractors. Aside from seeing your goals and having a clearly articulated implementation plan, a strong project proposal should also spell out who will take responsibility for everything from electricians to contractors to scheduling. If the contract is unclear or the sales reps sidestep the issue — walk away from the deal. It’s more valuable to pay for good service than to pay twice for bad service. 4.Installation Done Right: Avoid Costly Disruptions The most important question to ask a potential project management coordinator is “Can you guarantee installation that minimizes work interruptions?” Paying for project management is valuable, but only if the project management works. Demand a single point of contact, accessibility during installation and confirm a clear plan of responsibility for potential delays. Installation is one of the hidden costs of retrofit projects. On paper, coordinating your own retrofit installation reduces the project costs, sometimes significantly. In practice, your own lack of expertise can cause hiccups in the process that can cost valuable production time and staff time, and reduce the overall quality of your LED investment.It’s essential your project manager understands local, statewide and national energy codes. This is a key detail that may help you weed out the light bulb salesmen from the lighting experts. If no one is talking codes, then you’re more likely to be left with a liability than an upgrade. 5.Closeout Procedure: Don’t Walk Away Before You Measure Before you end the project, the company you hire should come in with reliable technology and measure the new light output in your space. If you don’t hit your foot candle goals or if the occupancy sensors aren’t working properly, your point of contact should make it right, at no additional cost. The final step in the close-out procedure – the rebate – should also be free of charge. Rebates can cover up to 50 percent of your total project costs when switching from an older or inefficient system. Push back if your project manager asks for rebate fees or guarantees a rebate as part of a price reduction plan. A rebate is an estimate and it’s critical to understand that rebates are not guaranteed. Local and state rebates can depend on the money available to the issuing agencies or factors outside the scope of your project. Utility providers qualify the availability of funds only at the start of projects and typically must visit your facility to validate the existing system compared to the LED system being installed. Relying on remaining available rebate dollars that may be exhausted prior to your approval and start date may leave you frustrated with your project. When you are ready to speak to someone about a lighting retrofit for your facility, contact our professionals at Worldwide Energy. After explaining the process of upgrading your lighting, you will see that our practices follow Mike’s guidelines laid out in the article. When you work with Worldwide Energy, you get an experienced and efficient team working hard to provide you with the best service available.

I feel partitions are not needed. You already have too much for the space. Adding a partition will shrink the space further. The simplistic solution, you do not wish to discard any furniture would be to paint all the walls in lighter pastles. And use some wall painting frames to highlight certain walls.