I agree with divadeva. More lights. If you can add pot lights do it. If they're already there add task lighting and up the wattage on the bulbs on the pot lights (replace with LED and you can make them brighter because the wattage on LED is lower for brighter light). If you have all of that add decorative lighting. If ventilation is an issue find a way to move the air around or add air filtration. Maybe the HVAC is deficient. Maybe you can add a HEPA filter instead of the standard one that comes with the unit. Call an HVAC specialist to see if there is a way to boost air flow in the room.

I am so happy to see you here! I will have to go back and see if i can retrieve my posts... thought I would make them into a little book for my daughter, with photos. Quick run-down on the bathroom (not travels, no time) - The kitchen has a rather elegant sliding door with beveled glass panels. Painted white, since this was the original colour. GD's new bathroom has the doors I had picked earlier; i thought of polishing them but decided sprayed automobile paint (on a resin primer) would wear better. Especially since it is such a small bathroom, and she is so splashy. I have this finish in my kitchen and it has lasted 15 years now. A tad chipped here and there, but only needs a wipe down once a week. Same finish for the balcony doors, also split like the bathroom. We have a new wardrobe, a study table with built-in shelves, and a small chest of drawers for her odds and ends. I want to re-tile the tiny balcony, more as a little statement. Currently we are looking at Portuguese tiles, though I did think a mosaic with a funky cat might be nice. Let me see the costing. The room will be painted a neutral adobe, with bright white woodwork and an off-white ceiling. This means she can go wild with cushions and covers. Other changes in the flat; We have changed the glass in the master bedroom and living room from small cramped panes to a single pane for each section with a 1" bevel all round. Doubles the cost of the glass, but looks so elegant! The air-conditioning is being re-located. The compressors were all mounted in the bedroom and living room balconies, which looked terrible and meant the balconies (very narrow, only 30" deep) couldn't be used for anything. Not even plants. So they are being moved so that the compressors can be mounted at the rear of the building. two down, one to go. Now we can put in some nice plants, fishtail palms etc. The kitchen counter on one side came out intact and will be reused elsewhere. I am planning overhead storage, cupboards, and a draining cupboard for plates and glasses. Right now there is no dish washer, though a place is earmarked, but for now I will put in a cupboard with steel racks for cups, glasses and plates, all hidden behind pressed glass doors. This is all in the planning stage.... Pictures in a little while, they are mostly on my ipad and don't transfer well to the mac. They come without numbers... so I have to rename the or something. Somebody tell me how to do this!

Following are my comments : 1.Buying cheaper branded sanitary fittings is only possible when you buy the same in bulk quantities. But I would like to highlight that these are one of the most important fixtures in the stated space. Don't compromise on the quality of it if you want them to survive the long run.(You can go for the Jaquar continental series or change to Parryware) You can certainly compromise on the WC & the WB since even brands like Somany give good ceramic fixtures at relatively low cost. There you can save your bucks. 2. I haven't worked on PVC vanity but can comment that marine ply cabinets also stand well for the wear and tear. 3. You can go ahead with just the glass partition avoiding the cubicle door. 4. Yes you can but the selection should be on the lighter side of the colour palette so that the bathroom should not look more claustrophobic due to its small size(2 m x 3.5m which is normal in today's real estate market in mumbai). Ar. Amol Bhopi AVB Architecture Mumbai 71.

Thank you so much for your response - and the encouragement. What I can do is buy a beadboard panel tall enough for an entire wall and have HD cut this down. I may find this to be a good deal less expensive anyway, though kits are cheap. Quality, I'm not so sure about. I'll just get the best I can. When I look at the sites that truly specialize in good-quality beadboard, thiers are also thin cladding and 32 inches high, so customizing is the way I'll need to go. The kits offer moldings that are exact fits, and this is attractive to me because I'll be asking for help with this from contractor who I think anticipates doing dry wall. It's a gift job, so want to make it very easy. I think the panels and moldings cut to size though will not be a problem. I'll get all supplies and corner mold, etc. I wonder now about back splash above marble vanity sink. How do y"all do it in your business if wainscot extends a little above the sink.